Alarm help guys!!!
Contents Introduction. 1 Display Status Blanking.2 IMPORTANT USER INFORMATION. Introduction Welcome to the eurosec control panel.
Monday 3rd January 2011
Need some help guys. Home alarm gone off and pad is saying bell tamp.
Thing is it happened once before and guy came out, pressed a few buttons and £70 thank you.
Anyone know if there somthing I can do? Tried reseting but just sets it off again.
Bell also randomly goes on and off
Appreciate some advice
Thanks
Thing is it happened once before and guy came out, pressed a few buttons and £70 thank you.
Anyone know if there somthing I can do? Tried reseting but just sets it off again.
Bell also randomly goes on and off
Appreciate some advice
Thanks
Monday 3rd January 2011
Monday 3rd January 2011
Monday 3rd January 2011
Monday 3rd January 2011
Monday 3rd January 2011
Did he to up a lsdder to do it?
there is usualy some kind of switch thst triggers if its taken off teh wall or if teh lid comes off. If this is normaly open circuit iwonder if moisture could have shorted it.
just a complete guess
there is usualy some kind of switch thst triggers if its taken off teh wall or if teh lid comes off. If this is normaly open circuit iwonder if moisture could have shorted it.
just a complete guess
Monday 3rd January 2011
No ladder, just few buttons on keypad, I assume he did some sort of reset?
Monday 3rd January 2011
from what I just goodled
'Have you tried it correctly, press quick then 1, or your user code then 1.
If none of this works you need to reprogramme the Gardtec Eurosec panel. Only an engineer can do that, unless you have the engineers code.'
no my bad engrish just copied and pasted from fixya
'Have you tried it correctly, press quick then 1, or your user code then 1.
If none of this works you need to reprogramme the Gardtec Eurosec panel. Only an engineer can do that, unless you have the engineers code.'
no my bad engrish just copied and pasted from fixya
Monday 3rd January 2011
from what I just goodled
'Have you tried it correctly, press quick then 1, or your user code then 1.
If none of this works you need to reprogramme the Gardtec Eurosec panel. Only an engineer can do that, unless you have the engineers code.'
no my bad engrish just copied and pasted from fixya
Read the same just now, going to try inabit as currently bell been off for abit but panel still showing fault'Have you tried it correctly, press quick then 1, or your user code then 1.
If none of this works you need to reprogramme the Gardtec Eurosec panel. Only an engineer can do that, unless you have the engineers code.'
no my bad engrish just copied and pasted from fixya
Thanks
Monday 3rd January 2011
and a user manual of a similar unit that might be worth a read:
http://www.rokonet.com/newsite/dynamicdata/flash/P...
http://www.rokonet.com/newsite/dynamicdata/flash/P...
Monday 3rd January 2011
No luck, going to have some pissed off neighbours tonight
Monday 3rd January 2011
Monday 3rd January 2011
Bellboxes have an anti-tamper pressure switch which trips when the lid is taken off. The switch has a metal strip on it and this can sometimes straighten out meaning that it no longer presses against the bellbox cover and so trips.
You need to take the cover off and see if you can bend the metal strip out again.
If you do this be extremely careful on a ladder, wear some ear protection in case bell goes off again and do not at any cost touch the strobe which can be hot.
If you have any doubts do not attempt this, call someone in.
You need to take the cover off and see if you can bend the metal strip out again.
If you do this be extremely careful on a ladder, wear some ear protection in case bell goes off again and do not at any cost touch the strobe which can be hot.
If you have any doubts do not attempt this, call someone in.
Tuesday 4th January 2011
Did he to up a lsdder to do it?
there is usualy some kind of switch thst triggers if its taken off teh wall or if teh lid comes off. If this is normaly open circuit iwonder if moisture could have shorted it.
just a complete guess....cos i splished asa rat an cant get my worms right
Fixed it for you Pesty.there is usualy some kind of switch thst triggers if its taken off teh wall or if teh lid comes off. If this is normaly open circuit iwonder if moisture could have shorted it.
just a complete guess....cos i splished asa rat an cant get my worms right
Tuesday 4th January 2011
If you do this be extremely careful on a ladder, wear some ear protection in case bell goes off again and do not at any cost touch the strobe which can be hot.
If you have any doubts do not attempt this, call someone in.
If you have any doubts do not attempt this, call someone in.
Tuesday 4th January 2011
cos i splished asa rat an cant get my worms right
Fixed it for you Pesty.
Fixed it for you Pesty.
there may have been a couple shots of whisky in me, but alas I fear it is a combination of wireless keyboard and being a bit thick that is the main culprit of my unintelligable posts and shockingly embarrasing spelling and punctuation .
Tuesday 4th January 2011
DIY link for tamper faults here
If you don't get any joy, drop me a PM and I will tell you which wires to link out at the control panel. At least that way you will know for sure whether it's wiring related, panel related or tamper switch related.
If you don't get any joy, drop me a PM and I will tell you which wires to link out at the control panel. At least that way you will know for sure whether it's wiring related, panel related or tamper switch related.
Tuesday 4th January 2011
If you do this be extremely careful on a ladder, wear some ear protection in case bell goes off again and do not at any cost touch the strobe which can be hot.
If you have any doubts do not attempt this, call someone in.
To be constructive rather than the strobe being hot, if the strobe flashes as you touch it you could get a nasty wollop of the thing, trust me it hurts If you have any doubts do not attempt this, call someone in.
So long as the bell cable hasn't been damaged, my guess will be a loose connection somewhere at the panel or bell, the tamper switch gone faulty at the bell or a dodgy bell fuse at the panel. To reset the panel after a tamper fault though you may need an engineer code.
Wednesday 5th January 2011
I knew you had to wait a few minutes and avoid touching it(as mentioned in my SAB manual) but couldn't exactly remember why!
Anyway, amounts to the same thing up a ladder: 'ouch' followed by 'Aaaaarrrgghh!'
Anyway, amounts to the same thing up a ladder: 'ouch' followed by 'Aaaaarrrgghh!'
Tuesday 8th March 2011
Pr5208 rev1.0 it says
Gassing Station | Homes, Gardens and DIY | Top of Page | What's New | My Stuff